|
|
| XRAY presents authentic option parts for XRAY T2, XRAY T2R, XRAY T2'007,XRAY T2'008, XRAY T2'009 and XRAY T3 cars: |
|
(click to enlarge) |
|
|
|
High-precision axial thrustbearing
Ceramic balls
Highest-quality material and design
Smoothest diff operation, increased lifespan
Extra-hard Si3N4 silicone nitride ceramic balls
Significantly improves differential lifespan
Reduces friction and vibration
Higher RPM capabilities |
|
(click to enlarge) |
#930238 Ceramic Ball-Bearing Axial F3-8 3x8x3.5
High-precision axial thrustbearing 3x8x3.5mm for ball differential features ceramic balls. Highest-quality material and design guarantees the smoothest diff operation and increased life. Ceramic balls in the axial cage are made from extra-hard Si3N4 silicone nitride ceramic. Significantly improves differential lifespan while reducing friction and vibration. Higher RPM capabilities. |
|
|
| Fits: T1, T1 EVO2, T1R, T1 FK, T1 FK05, T2, T2R, T2'007, T2'008, T2'009, T2R PRO, T3, XII, XII Link, X10. |
|
(click to enlarge) |
#930250 Ceramic Axial Thrustbearing F5-10 5x10x4
High-precision axial thrustbearing 5x10x4mm for XCA clutch features ceramic balls. Highest-quality material and design guarantees the smoothest clutch operation and increased life. Ceramic balls in the axial cage are made from extra-hard Si3N4 silicone nitride ceramic. Significantly improves lifespan while reducing friction and vibration. Higher RPM capabilities. |
|
|
| Fits: NT1 cars. |
|
(click to enlarge) |
|
|
|
#303035 Alu Quick Roll-Center Holder 4.9mm H1 + H2
4.9mm Quick Roll Center holders
CNC-machined high-grade aluminum
Matched pair marked H1 & H2
Roll centers higher by 1mm
For either front or rear suspension
Best on high-traction tracks
Fits T2- or T3-based cars |
|
(click to enlarge) |
|
|
|
XRAY presents yet another way to fine-tune your T2- or T3-based car with new 4.9mm Quick Roll Center holders. This matched pair of CNC-machined high-grade aluminum holders marked H1 and H2 are 1mm higher with the same length than L1 + L2 (lower) holders, allowing car to roll more. May be used at either front or rear.
Using the H roll-center holders in the front makes the car turn easier. Recommended for high-carpet traction tracks because it decreases in corner steering and helps to prevent traction rolling.
Using the H roll-center holders in the rear increases corner steering and speed. |
|
(click to enlarge) |
|
|
|
| Fits: T2, T2R, T2'007, T2'008, T2'009, T2R PRO, T3 cars. |
|
(click to enlarge) |
|
|
|
#302665 Composite Ball Joint 4.9mm - Closed with Hole (4)
Molded composite steering ball-joint
For T2/T3 family of cars
Fits 5mm pivot ball or ball stud
Prevents dust fouling of ball end
Easy assembly/disassembly
Easy movement of upper camber links
Use with ball ends #302653, #302654 or #302655, available in three lengths |
|
(click to enlarge) |
|
|
|
Molded composite steering ball-joint for T2 family of cars and T3. Fits 5mm pivot ball or ball stud. Set of 4.
The closed ball joint prevents dust from getting onto the ball end and the incorporated hole allows for easy assembly and disassembly. Allows easy movement of the upper camber links. These ball joints must be used with ball ends #302653, #302654 or #302655, which are available in three lengths for front and rear suspension.
Fits: T2, T2R, T2'007, T2'008, T2'009, T2R PRO, T3 cars. |
|
(click to enlarge) |
|
|
(click to enlarge) |
|
|
|
Optional 1-piece aluminum rear suspension holder is a direct replacement for the standard forward holders of the REAR suspension. This holder is narrower than the rearward holder of the REAR suspension but keeps the same width of the car as with standard T3 holders. The aluminum suspension holder reinforces the chassis and helps prevent chassis damage in extreme hard crashes.
Fits: T3 cars. |
|
(click to enlarge) |
|
|
(click to enlarge) |
|
|
|
| XRAY presents new additions to the range of precision-molded 64-pitch offset spur gears made from special hard composite material, strategically lightened to reduce rotating mass without compromising strength or durability. The addition of new 92T, 96T, and 100T gears allows you to further fine-tune your car's performance. With these original XRAY spur gears, you can race with confidence. |
|
(click to enlarge) |
|
|
|
#930220 Ceramic Ball 2.4mm (12)
#930230 Ceramic Ball 3.175mm (12)
Set of 12 premium-quality ceramic balls
Extra-hard Si3N4 silicone nitride ceramic
Significant improvement of differential lifespan
Reduces friction & vibration
Higher RPM capabilities
Set of 12 premium-quality ceramic balls made from extra-hard Si3N4 silicone nitride ceramic. Significantly improves differential lifespan while reducing friction and vibration. Higher RPM capabilities. |
|
(click to enlarge) |
|
|
|
| High-speed ceramic diff balls have very high durability (when properly lubricated) due to reduced slip and heat. With ceramic being approximately 60% lighter than steel, ceramic diff balls have a significantly lower rotating mass. Together this means that the lifespan of ceramic diff balls is 3-5 times longer than that of steel diff balls under matching conditions. Ceramic diff balls have vastly-superior corrosion resistance over steel diff balls, and with an inherent low-friction coefficient and smooth surface, frictional forces on ceramic diff balls are much lower. |
|
(click to enlarge) |
|
|
(click to enlarge) |
|
|
(click to enlarge) |
|
|
|
| These new 40T, 42T, 44T, 46T, 48T and 50T 64-pitch narrow high-performance pinion gears are manufactured from special lightweight aircraft duraluminum are 1.5mm thinner and 25% lighter than the regular-size pinion gears. |
|
(click to enlarge) |
High-performance pinions
Super narrow design
Lightweight aircraft duraluminum
Hardcoated
1.5mm thinner
Manually inspected
Individually run-in
Fits all touring cars |
|
|
| These narrow pinions are manufactured by XRAY on a specially-modified precision gear machine which has ultra-precise tolerances and assures unparalleled concentricity. After machining, the edges of pinions are chamfered and then the pinions are run in. The pinions are then specially treated to give them an even hardcoating so they stay absolutely true for a long time. The pinions run great with any spur gears, and work perfectly with XRAY spur gears where even throttle on/off noise nearly disappears. You can be confident in using the new narrow pinion right from the package, knowing that you are using a pinion of leading-edge design and production. |
|
(click to enlarge) |
|
|
|
| Fits: T1, T1 EVO2, T1R, T1 FK, T1 FK05, T2, T2R, T2'007, T2'008, T2'009, T2R PRO, T3, XII, XII Link, X10. |
|
(click to enlarge) |
|
|
|
Closed ball joint assembly
For T2 family cars
Composite closed ball joints
Threaded front & rear ball ends |
|
(click to enlarge) |
|
|
|
#302653 Ball End 4.9mm With Thread 6mm (2)
Threaded 4.9mm ball end with 6mm thread for rear suspension on T2 family of cars to replace the ball + screw assembly. These balls are great for use with closed composite ball joints #302661 but also work with standard open ball joints. Set of 2.
Fits: T2, T2R, T2'007, T2'008, T2'009, T2R PRO, T3. |
|
(click to enlarge) |
|
|
|
#302654 Ball End 4.9mm With Thread 8mm (2)
Threaded 4.9mm ball end with 8mm thread for front suspension on T2 family of cars to replace the ball + screw assembly. These balls are great for use with closed composite ball joints #302661 but also work with standard open ball joints. Set of 2.
Fits: T2, T2R, T2'007, T2'008, T2'009, T2R PRO, T3. |
|
(click to enlarge) |
|
|
|
#302655 Ball End 4.9mm With Thread 10mm (2)
Threaded 4.9mm ball end with 10mm thread replaces ball+screw assembly on front suspension of the T2 & T3 family of cars. These ball ends are great for use with closed composite ball-joints #302661 but also work with standard open ball-joints. Set of 2.
Fits: T2, T2R, T2'007, T2'008, T2'009, T2R PRO, T3. |
|
(click to enlarge) |
|
|
|
#302661 T2 Composite Ball Joint 5mm - Closed (4)
Molded composite steering ball-joint for T2 family of cars. Fits 5mm pivot
ball or ball stud. Set of 4.
The closed ball joint prevents dust from getting onto the ball end, allowing
the upper camber links to move more freely. The closed ball joints must be used with ball ends #302653 or #302654; these ball ends are available in two lengths for front and rear suspension, respectively.
Fits: T2, T2R, T2'007, T2'008, T2'009, T2R PRO, T3. |
|
(click to enlarge) |
|
|
|
Set of CNC-machined FRP chassis and front/rear upper decks for T2R PRO.
The main advantage of the FRP material is its flex allowance. Due to the flex, the chassis and top decks create more traction and stability on low-traction asphalt tracks compared to standard graphite material.
Knowing that every small detail impacts the handling and performance of a high-performance car, XRAY CNC-machines every chassis in-house using the most modern German milling machines. fully robotically-operated and controlled to ensure that every chassis meets the tightest manufacturing tolerances.
Fits: XRAY T2009, T2008, T2R PRO |
|
(click to enlarge) |
|
|
(click to enlarge) |
|
|
|
Increases upper linkage length
Premium Swiss 7075 T6 aluminum
Hard-anodized & black coated
For front or rear suspension
Fits all T2 cars |
|
(click to enlarge) |
#303033 Alu Quick Roll-Center Holder 4.9mm - L1+L2 (2)
New 4.9mm alu quick roll-center holders allows you to make the upper linkage longer in either front or rear suspension of all T2-based cars. Includes a pair of roll centers marked L1 and L2.
Fits: T2, T2R, T2'007, T2'008, T2'009, T2R PRO, T3. |
|
|
| Using the 4.9mm roll-center holders in the front makes the car turn easier and more precisely. Using the 4.9mm roll-center holders in the rear increases steering and cornering speed. |
|
(click to enlarge) |
|
|
(click to enlarge) |
|
|
|
Lightweight turnbuckles
7075 T6 Swiss aluminum
Precision threads
Super strong
Hardcoated with black finish
Lighter by 50% |
|
(click to enlarge) |
#302612 Alu Adjustable Turnbuckle M3 L/R 39mm - 7075 T6 (2)
Adjustable left & right M3 steering turnbuckles manufactured from strong, lightweight 7075 T6 aluminum. Precision threading for fine toe adjustment. Length of 39mm. Set of 2.
For serious racers who are conscious of weight savings, XRAY offers lightweight alu turnbuckles. Lighter by 50%.
Fits: T2, T2R, T2'007, T2'008, T2'009, T2R PRO, T3. |
|
(click to enlarge) |
|
|
(click to enlarge) |
#303212 Alu Adjustable Turnbuckle M3 L/R 26mm - 7075 T6 (2)
Adjustable left & right M3 steering turnbuckles manufactured from strong, lightweight 7075 T6 aluminum. Precision threading for fine toe adjustment. Length of 26mm. Set of 2.
For serious racers who are conscious of weight savings, XRAY offers lightweight alu turnbuckles. Lighter by 50%.
Fits: T2, T2R, T2'007, T2'008, T2'009, T2R PRO, T3. |
|
(click to enlarge) |
|
|
(click to enlarge) |
|
|
|
#300944 T2'009 - Rubber-Spec Conversion Set - 38T Pulley
changes the initial ratio from 1.7 to 1.9
includes 38T composite solid axle, 38T diff pulley, new front & rear belts
improves on/off throttle response
increases stability
makes car easier to drive
recommended for all surfaces and traction conditions
fits for T2 009 EU and T2R Pro
|
|
(click to enlarge) |
|
|
|
| New 38T conversion set for the T2'009EU and T2R Pro changes the internal transmission ratio from 1.7 to 1.9. Set includes top-quality 38T composite solid axle and 38T diff pulley, plus new front & rear belts to fit the new pulleys. Improves on/off throttle response, increases stability and makes the car easier to drive. Recommended for all surfaces and traction conditions. |
|
(click to enlarge) |
|
|
|
| Fits: T2'009 EU Edition and T2R PRO |
|
(click to enlarge) |
|
|
|
#300943 T2'009 - Rubber-Spec Conversion Set - Forward Motor Position
allows more forward motor position
no chassis change required
includes front & rear graphite upper decks, 38T composite solid axle, 38T diff pulley, forward motor position front & rear belts
increases on-power steering
makes car turn more easily and precisely
fits for T2'009 EU and T2R Pro
|
|
(click to enlarge) |
|
|
|
| New forward motor position conversion set for the T2'009EU and T2R Pro allows for a more forward motor position without changes to the chassis. Set includes top-quality front & rear graphite upper decks, 38T composite solid axle, 38T diff pulley, and forward motor position front & rear belts. |
|
(click to enlarge) |
|
|
|
| Increases on-power steering, and makes the car turn more easily and precisely. |
|
(click to enlarge) |
|
|
|
| Fits: T2'009 EU Edition and T2R PRO 6-cell chassis only |
|
(click to enlarge) |
|
|
|
#309860 LiPo Balancing Chassis Weights
LiPo balancing weights
Compensates for lightweight LiPo
Balances L/R sides of the car
Weight in center of chassis
Improves reaction & roll
Prevents battery pack to move
CNC-machined from brass
Complete set
Fits 6 cell chassis |
|
(click to enlarge) |
|
|
|
Excellent and unique chassis weights for use with LiPo battery pack.
Due to the light weight of LiPo batteries, your car may not be perfectly balanced. The LiPo balancing chassis weights are developed to help balance the left and right sides of the car. The weights are situated in the center of the chassis to keep the weight in the center of the car for better reaction and roll. Batteries are moved outward so they can be more easily inserted; aluminium holders prevent batteries from coming out.
Fits: T2'008, T2'009 and T2R PRO 6-cell chassis only |
|
(click to enlarge) |
|
|
|
Strong rear shock tower for T2'008, T2'009 & T2R PRO
Extra-thick 3.5mm high-grade graphite
Increased strength and reliability
For high-competition racing or extreme racing conditions
New strong rear shock tower for T2'008,T2'009 & T2R PRO is CNC-machined from premium extra-thick 3.5mm high-grade graphite to minimize breakage. Features same shock and roll center positions as the stock shock tower but with increased strength and reliability for high-competition racing or extreme racing conditions. A great option part to help insure a safe drive. |
|
(click to enlarge) |
|
|
|
| Fits: T2'008, T2'009 and T2R PRO. |
|
(click to enlarge) |
|
|
(click to enlarge) |
| New narrow high-performance pinion gear manufactured from special lightweight aircraft duraluminum is 1.5mm thinner and 25% lighter than the regular-size pinion gear. Available in 48pitch (12-34T) and 64pitch (18-38T). Perfect for the T2 family of cars. |
|
(click to enlarge) |
These new narrow pinions are manufactured by XRAY on a specially-modified precision gear machine which has ultra-precise tolerances and assures unparalleled concentricity. After machining, the narrow pinions have all their edges chamfered and then are run-in. The pinions are then specially treated to give them an even hardcoat so they stay absolute true for a long time. The pinions run great with any spur gears, and work perfectly with XRAY spur gears where even throttle on/off noise disappears. You can be confident in using the new narrow pinion right from the package, knowing that you are using a pinion of leading-edge design and production.
Fits: XRAY T1, T1 EVO2, T1R, T1 MINI, T1 FACTORY KIT, T1FK '05, T2, T2R, T2'007, T2'008, T2'009, T2R PRO and T3. |
|
(click to enlarge) |
|
|
(click to enlarge) |
309840 Precision Balancing Chassis Weights
A complete set of 4 chassis balancing weights (2x 5g + 2x 10g) and mounting hardware. Designed for XRAY electric & nitro touring car to be mounted at pre-drilled chassis holes; also fits other race cars as well. Made from steel and laser engraved with the weight value for easy identification.
|
|
(click to enlarge) |
| For precision balancing, use the #107880 HUDY Chassis Balancing Tool. Place the chassis (using the two holes drilled along the centerline of the chassis) onto the tips of the balancing tool. If the chassis falls to one side, it is not balanced, and weight needs to be added to the other side. Add balancing weights to the chassis as required until the chassis stays level when placed on the chassis balancing tool. |
|
(click to enlarge) |
When possible, weights should be mounted to the pre-drilled chassis holes.
The set consists of:
5g weights (2pcs)
10g weights (2pcs) |
|
|
Besides looking great, these weights can be stacked atop each other in order to achieve the proper chassis balance.
Fits: XRAY T1, T1 EVO2, T1R, T1 MINI, T1 FACTORY KIT, T1FK '05, T2, T2R, T2'007, T2'008, T2'009, T2R PRO, T3 and NT1. |
|
(click to enlarge) |
|
|
(click to enlarge) |
| The ECS drive shafts equalize the speed between the drive shaft and the wheel. With a unique 2-piece joint between the axle and the wheel, the same extreme wheel turning angle is divided into two shallower angles without joint binding. This means that at the same cornering speed, the inner wheel will not bind or vibrate. Drive through the corner is more stable, more precise and easier to drive. |
|
|
With the new ECS drive shafts, wheel vibrations and noise are decreased to minimum, steering is increased and cornering speed and smoothness increases noticeable.
The ECS drive shafts come factory pre-assembled for quality checking, but it is not immediately ready to use. Before using follow the instruction manual.
NOTE: To use the ECS drive shafts you need to use the front C-hubs V2 with the larger opening. The C-hubs V2 were included in all T2'008 kits, so owners of the T2, T2'007 and T2R must purchase the C-hubs V2 separately.
Fits: XRAY T2, T2R, T2'007, T2'008, T2'009, T2R PRO and T3. |
|
(click to enlarge) |
|
|
(click to enlarge) |
|
|
(click to enlarge) |
|
|
(click to enlarge) |
303440 Alu Anti-Roll Bar Collar (2)
Alu anti-roll bar collars remove play from the front anti-roll bar wire, increasing cornering speed and stability. Intended for serious racers who desire maximum performance from their car. Fits all T2 cars. Set of 2 collars and setscrews.
Fits: XRAY T2, T2R, T2'007, T2'008, T2'009, T2R PRO and T3. |
|
(click to enlarge) |
|
|
(click to enlarge) |
|
|
(click to enlarge) |
These high-performance drives shafts are available in 50mm and 52mm sizes:
a.) 50mm drive shafts for use in US editions of T2 platform cars
b.) 52mm drive shafts for use in EU editions of T2 platform cars |
|
|
Precision-machined with highest tolerances using premium fully-automatic German CNC-machines. High-quality hardcoating is done at XRAY's own inhouse fully-robotic hardcoating line, ensuring a perfect hardcoated surface every time on every piece.
Fits: XRAY T2, T2R, T2'007, T2'008, T2'009, T2R PRO and T3. |
|
(click to enlarge) |
|
|
(click to enlarge) |
Strategically machined for toughness and light weight without compromising strength. Reduces rotating weight by up to 35% over standard outdrive.
Fits: XRAY T2, T2R, T2'007, T2'008, T2'009, T2R PRO and T3. |
|
(click to enlarge) |
|
|
(click to enlarge) |
The alu driveshaft adapters for the front solid axle are a direct replacement for the stock composite versions but with increased the strength and lifespan.
The modular design of the front solid axle allows for easy removal and servicing. Internal slots key to drive shaft pins require use of driveshaft blades #305241 (included), enabling direct power transfer to the wheels and eliminating excess play between the outdrives and drive shafts. Set of 2. |
|
(click to enlarge) |
Precision machined with highest tolerances using premium fully-automatic German CNC-machines. High-quality hardcoating is done at XRAYs own in-house fully-robotic hardcoating line, ensuring a perfect hardcoated surface every time.
Fits: XRAY T2'008, T2'009, T2R PRO and T3. |
|
(click to enlarge) |
|
|
(click to enlarge) |
303071 Belt Tensioner Set T2'007, T2'008
Smart, easy-to-use XRAY Belt Tensioner Set for controlling center drive belt tension and twisting. High-quality components include CNC-machined lightweight alu mounting post, high-speed ball-bearings, and mounting hardware.
Fits: XRAY T2'007, T2'008, T2'009, T2R PRO and T3. |
|
(click to enlarge) |
|
|
(click to enlarge) |
|
|
(click to enlarge) |
308306 XRAY T2'008 Alu Shock Absorber - Set (2)
Premium XRAY aluminum shock absorbers are specially developed and designed to work with T2008. These unique black hardcoated aluminum shocks are loaded with all of the features needed for todays racing. When you need ultra-fine shocks for your lightweight electric touring car, the new XRAY shocks have you covered. |
|
(click to enlarge) |
| The unique XRAY aluminum shock absorbers have interchangeable internal parts, with fixed 1-piece precision pistons which are available with 3 different-diameter holes for damping adjustment: 1.1mm, 1.2mm, and 1.3mm holes. No matter what you choose, all pistons are ultra-true and round thanks to a very special mould design, resulting in ultra-free movement of the piston inside the shock body. |
|
(click to enlarge) |
| The XRAY aluminum shock absorbers come with all the necessary parts to build one pair of shocks (2 shocks). Springs and shock oil are not included and must be purchased separately. |
| Features |
|
The aluminum shock body is precision CNC-machined on the worlds most precise German long-turn CNC machine and every piece is robotically-inspected and measured to ensure maximum precision and tolerance. This is especially important with the inner diameter of the shock body to ensure that each one has an identical inner diameter to guarantee ultra-free shock piston movement.
The aluminum shock body is machined from exclusive Swiss 7075 T6 aluminum ensuring maximum strength and rigidity. The shock bodies are black hardcoated using XRAYs own fully robotic colorcoating line with purpose-mixed color fluids, ensuring a very even layer of color coating is applied to each shock body. After the coating process, every shock body is manually checked with high-precision calipers to ensure that the inner diameter of each shock body is exactly within the very stringent tolerances.
The shock cartridge has been designed for self-centering shim(s) to hold silicone O-rings, guaranteeing perfect alignment in the shock body. A finely-threaded aluminum shock lower cap secures the silicone O-rings and shims in the shock body.
Finely-threaded spring preload collars are used to make ride height quick and easy. Even in very dirty conditions it is still possible to very precisely adjust ride height.
The upper aluminum cap features a small vent hole which makes shock assembly very predictable and easy, since excess shock oil will escape through this vent hole ensuring that the proper amount of the oil remains inside the shock assembly. A super-soft silicone membrane supported by a miniature foam pad (inserted inside the membrane) provides proper dampening characteristics.
Fits: T2008, T2'009, T2R PRO and T3. |
|
|
|
|
|
|
|
(click to enlarge) |
301185 T2 008 Asphalt-Spec Upper Deck Graphite + Rear Upper Deck - Set
CNC-machined front and rear upper deck of premium-grade graphite material, specially designed and optimized for rubber-tire racing conditions. The narrow design provides appropriate torsion and flex, and the elongated profile reduces unwanted tweak in crashes. |
|
(click to enlarge) |
New thinner 2mm top deck makes the car easier to drive because it increases overall traction. We recommend using this optional top deck on low-traction tracks mainly on asphalt but can be also used on low-traction carpet.
Fits: T2008, T2'009, EU edition only and T2R PRO. |
|
(click to enlarge) |
|
|
(click to enlarge) |
302054 T2 008 Alu Chassis Brace
Alu chassis brace for T2'008 is CNC-machined from high-grade aluminum. It is recommended for carpet tracks with medium to super-high traction. Also suggested to use when the used tires have a lot of natural traction (for example soft compound tires) but also for tires which have type of insert which create a lot of air inside the tire. This will make the car easier to drive with smoother steering and the car will not "stop" in the corner.
Fits: XRAY T2'008, T2'009, T2R PRO and T3. |
|
(click to enlarge) |
|
|
(click to enlarge) |
|
|
(click to enlarge) |
|
|
(click to enlarge) |
|
|
(click to enlarge) |
305104 XRAY Multi-Diff T2 008
The unique Multi-Diff caused a sensation in RC car racing when it was first introduced, and the updated version is no different. The Multi-Diff has 3 different settings:
Standard one-way :
Left and right outdrives turn independently off-power, both lock on-power.
Solid one-way :
Left & right outdrives turn together off-power, both locked on-power
Solid axle :
Full-time solid axle |
|
(click to enlarge) |
| The lightweight one-way outdrives manufactured from Hudy Spring Steel have a hex-slot machined at each end, into which a lightweight machined steel hex-style locking axle can be inserted into both outdrives to lock them together. This allows the creation of a solid one-way, meaning that both outdrives turn freely together as a one-way (at the same time), thus creating a solid one-way off-power. |
|
(click to enlarge) |
To create a full-time solid axle, a strong steel pin is inserted through aligned holes in the main aluminum body of the Multi-Diff and the steel locking axle. This locks the outdrives completely, creating a full-time solid axle.
Includes factory-pressed (non-replaceable) high-quality German one-way bearings, hand-ground for maximum running precision and strength. The one-way bearings must be serviced, cleaned, and oiled regularly (we recommend using #309580 One-way Lube). |
|
|
The innovative #305104 XRAY Multi-Diff has been updated for use ONLY on the XRAY T2008; it is not interchangeable with other versions of the Multi-Diff.
Fits: XRAY T2'008, T2'009, T2R PRO and T3. |
|
(click to enlarge) |
|
|
(click to enlarge) |
303095 T2 Shock Tower Rear 3.5mm Graphite - Ultra Strong
This stronger rear shock tower for T2 & T2'007 is CNC-machined from premium extra thick 3.5mm graphite. This will minimize breakage and is a great valuable option part for any drivers who want to have a safe drive.
Fits: XRAY T2, T2R and T2'007. |
|
(click to enlarge) |
|
|
|
300941 T2 007 - US Foam-Spec Edition - Conversion Set
Conversion set for T2/T2R cars to update them to the T2007 US Foam-Spec Edition. Included parts listed in parts list section.
Parts included:
301123 Chassis 3.5mm - 1pcs included
301179 Upper Deck - Wide - 1pcs included
302018 Front Bulkhead - 2pcs included
302078 Composite Hubs - 4pcs included
302162 Front Arm - 2pcs included
302504 XRAY Quick-Saver - 1pcs included
302581 Servo Horn - KO - 1pcs included
302583 Servo Horn - Futaba - 1pcs included
302630 Adj. Turnbuckle - 1pcs included
302652 Ball End - 1pcs included
303018 Rear Bulkhead - 2pcs included
303019 Right Layshaft Bulkhead - 1pcs included
303029 Motor Mount Bulkhead - 1pcs included
303044 Rear Upper Deck - 1pcs included
303162 Rear Arm - 2pcs included
305886 Spur Gear 116T/64 - 1pcs included
306513 Top Deck Mount - 4pcs included
308387 Springs Light-Purple - 2pcs included
308394 Springs White - 2pcs included
391009 Instruction Manual - 1pcs included
960140 Nut M4 with Flange - 4pcs included
Exploded View & Spare Parts List - 1pcs included
Set-Up Sheet - Foam - 1pcs included
Fits: XRAY T2 and T2R. |
|
|
|
|
(click to enlarge) |
|
|
|
300942 T2 007 - EU Rubber-Spec Edition - Conversion Set
Conversion set for T2/T2R cars to update them to the T2007 EU Rubber-Spec Edition. Included parts listed in parts list section.
Parts included:
301122 Chassis 2.5mm - 1pcs included
301179 Upper Deck - Wide - 1pcs included
302018 Front Bulkhead - 2pcs included
302078 Composite Hubs - 4pcs included
302504 XRAY Quick-Saver - 1pcs included
302581 Servo Horn - KO - 1pcs included
302583 Servo Horn - Futaba - 1pcs included
302630 Adj. Turnbuckle - 1pcs included
302652 Ball End - 1pcs included
303018 Rear Bulkhead - 2pcs included
303019 Right Layshaft Bulkhead - 1pcs included
303029 Motor Mount Bulkhead - 1pcs included
303044 Rear Upper Deck - 1pcs included
303162 Rear Arm - 2pcs included
306513 Top Deck Mount - 4pcs included
391009 Instruction Manual - 1pcs included
960140 Nut M4 with Flange - 4pcs included
Exploded View & Spare Parts List - 1pcs included
Set-Up Sheet - Rubber - 1pcs included
Fits: XRAY T2 and T2R. |
|
(click to enlarge) |
|
|
(click to enlarge) |
305590 Alu Middle One-Way Pulley Set
High-quality middle one-way pulley set for XRAY T2 cars is a great option part especially for rubber tires on carpet tracks or asphalt tracks. Recommended by Team XRAY for all levels of drivers from beginners to pros. The middle one-way can be used in combination with a front one-way diff which will make the car easier to drive, smoother, and have increased steering. |
|
(click to enlarge) |
Set includes precision-balanced layshaft, CNC-machined high-strength alu pulleys, spur gear mounting plate, top-quality sealed ball-bearings, and mounting hardware. One pulley is keyed to layshaft, other pulley contains high-grade precision hand-ground one-way bearing for ultra-smooth operation. Spur gear not included.
Fits: XRAY T2, T2R and T2'007. |
|
(click to enlarge) |
|
|
(click to enlarge) |
305186 Delrinฎ Solid Axle Body - Lightweight
For serious racers looking for an edge, XRAY's new ultra-true, high-durability solid front axle body is CNC machined from lightweight Delrinฎ composite material, making it 25% lighter than the original Multi-Diff. This solid axle transforms the XRAY Multi-Diff into a full-time solid axle only; remaining parts must be used from the Multi-Diff.
Fits: All XRAY touring cars, except T2'008, T2'009, T2R PRO and T3. |
|
(click to enlarge) |
|
|
(click to enlarge) |
|
|
|
Wide range of CNC-machined, premium aircraft aluminum offset wheel hubs and shims for XRAY T2 allow you to precisely adjust the track-width of your T2 by fine increments. These clamping-style wheel hubs are strategically machined for optimum strength, balance, and lightness, and are marked for easy identification. Hubs offered in offsets of -0.75mm, +0.75mm, +1.5mm, and a 0.75mm shim is also available.
305350 T2 Alu Wheel Hub (2)
305351 T2 Alu Wheel Hub - Offset -0.75mm (2)
305352 T2 Alu Wheel Hub - Offset +0.75mm (2)
305353 T2 Alu Wheel Hub - Offset +1.5mm (2)
305380 Alu Wheel Shim Offset 0.75mm (2)
Fits: XRAY T2, T2R, T2'007, T2'008, T2'009, T2R PRO and T3. |
|
(click to enlarge) |
|
|
|
Precision moulded 64 pitch gears for the XRAY touring cars. All gears are made from XRAY's exclusive secret blend of plastic, allowing the gear to run true, be super quiet and robust enough to handle low wind mod motors. The spur gears are strategically designed to have the lowest possible weight while keeping them strong and light. Each gear is stamped with a tooth number for easy identification.
Available in all popular sizes, allowing you to find the perfect gear ratio for any track.
305882 Spur Gear 112T/64
305884 Spur Gear 114T/64
305886 Spur Gear 116T/64
305888 Spur Gear 118T/64
Fits: All XRAY touring cars. |
|
(click to enlarge) |
|
|
(click to enlarge) |
|
|
(click to enlarge) |
|
|
(click to enlarge) |
|
|
(click to enlarge) |
301203 T2 Impact-Absorbing Front Bumper
Impact -absorbing front bumper for XRAY T2 is made from high-quality nylon that absorbs the energy from crashes.
Fits: XRAY T2, T2R, T2'007, T2'008, T2'009, T2R PRO and T3. |
|
(click to enlarge) |
302256 T2 Alu Steering Block
Alu Steering Block for XRAY T2 is CNC-machined from premium lightweight T6 aluminum, polished for luxuriuous and stylish appearance. Ultra-strong construction provides very long life and durability in even the most extreme racing conditions. Composite bushings are used to secure the ball-bearings in both sides of this steering block; this allows the ball-bearings to fit perfectly and turn freely, giving much higher lifetime compared to bearings installed directly into aluminum steering blocks. Includes two nylon bushings and two ball-bearings. Fits left or right sides.
Fits: XRAY T2, T2R, T2'007, T2'008, T2'009, T2R PRO and T3. |
|
(click to enlarge) |
302401 T2 Anti-Roll Bar Front (Set)
303401 T2 Anti-Roll Bar Rear (Set)
If your XRAY T2 is understeering, then try this optional front or rear anti-roll bar set. The front & rear anti-roll bars will decrease front or rear chassis roll and decrease front or rear traction, increasing your cars steering. This complete rear anti-roll bar set for the XRAY T2 includes all necessary hardware, and includes three different anti-roll bars: 1.2, 1.4, and 1.6mm.
Fits: XRAY T2, T2R, T2'007, T2'008, T2'009, T2R PRO and T3. |
|
(click to enlarge) |
303060 Graphite Motor Guard
CNC-machined graphite motor guard for T1FK05 and T2 protects the motor endbell from collisions. Includes mounting hardware.
Fits: XRAY T2, T2R, T2'007, T2'008, T2'009, T2R PRO and T3. |
|
(click to enlarge) |
Composite bushings are used to secure the ball-bearings in both sides of this rear upright; this allows the ball-bearings to fit perfectly and turn freely, giving much higher lifetime compared to bearings installed directly into aluminum uprights. Includes composite bushings and ball-bearings. Fits XRAY T2.
Fits: XRAY T2, T2R, T2'007, T2'008, T2'009, T2R PRO and T3. |
|
(click to enlarge) |
306163 T2 Graphite Battery Strap w/ Alu Stands (Set)
Pre-assembled graphite battery strap for XRAY T2 features the XRAY smart battery holder system and new battery tweak-free mounting system. The alu capture wheel enables you to easily close and secure the battery strap without any clips.
The new battery tweak-free mounting system works with the Multi-Flex Technology(TM) concept; the redesigned capture wheel gives sufficient play and will not stiffen the chassis even when the wheel is tightened excessively.
Fits: XRAY T2, T2R, T2'007, T2'008, T2'009, T2R PRO and T3. |
|
|
| Alu parts are polished for promotion purposes. |
|
