|
|
News |
|
|
|
|
(click to enlarge) |
|
|
(click to enlarge) |
|
|
|
M18 PRO chassis set in different stylish graphite finish. Includes CNC-machined graphite parts (chassis, top deck, battery holder and top bumper upper holder), molded composite parts (battery backstops, rear bumper), alu LiPo battery strap posts and mounting hardware. |
|
(click to enlarge) |
|
|
(click to enlarge) |
|
|
(click to enlarge) |
|
|
(click to enlarge) |
|
|
(click to enlarge) |
⢠Micro pinion gears
⢠For standard micro motors
⢠48 pitch modul
⢠High-performance
⢠Tough & durable
⢠Steel material
⢠Precision-cut
⢠Chamfered edges
⢠Run-in
⢠Indvidually inspected
⢠Complete range available
|
|
|
High-performance 9 tooth, 48-pitch micro pinion gear, manufactured from special steel for toughness and durability. Precision-cut teeth with chamfered edges. Run-in for smooth operation. |
|
(click to enlarge) |
|
|
|
Fits: M18, M18PRO, M18T, M18MT. |
|
|
************************************************************************************************* |
|
(click to enlarge) |
|
|
(click to enlarge) |
389912 Wheel Aerodisk M18 PRO (Hex Hub) - Rubber (2+2)
Solid dish rims for rubber tires. Wheels for use with drive shafts with hex adaptors ONLY. Will not fit on original M18 with original wheel mounting system. Set of 4 (front and rear).
Fits: M18 PRO
Will also fit M18/NT18 when used with drive shafts with hex adaptors and #385262 alu nuts. |
|
|
************************************************************************************************* |
|
(click to enlarge) |
|
|
|
************************************************************************************************* |
|
(click to enlarge) |
|
|
(click to enlarge) |
CNC-machined alu micro wheel axles for drive shafts with hex adaptors are made from tough, high-grade T6 aluminum. Ultra-smooth operation, high-precision design and fit. Provides extra strength for use with high-performance motors. Features 1.0mm and 2.0mm offset for wider track-width.
For use with hex-hub micro wheels only; will not fit original M18. Set of 2.
385253 M18PRO Alu Wheel Axle - Offset +1mm (2)
385254 M18PRO Alu Wheel Axle - Offset +2mm (2) |
|
|
************************************************************************************************* |
|
(click to enlarge) |
|
|
(click to enlarge) |
XRAY introduces a new 5-cell (6.0V) and a new 6-cell (7.2V) inline battery packs made from ultra-high performance Intellect IB1400mAh NiMH cells. These 2/3A cells offer low resistance and they will maintain their high voltage under load, allowing them to easily provide power to high-powered servos without a performance decrease. |
|
|
************************************************************************************************* |
|
(click to enlarge) |
|
|
(click to enlarge) |
385203 Alu Drive Shaft with Hex Adapter - Set (2)
CNC-machined drive shafts with hex adaptors are made from tough, high-grade T6 aluminum and high-strength steel pins and fasteners. Ultra-smooth operation, high-precision design and fit. Provides extra strength for use with high-performance motors. This set of two drive shafts comes completely assembled, ready to install. A "must have" for serious drivers involved in high-competition racing. For use with hex-hub micro wheels only.
Fits: M18 PRO
Will also fit M18/NT18 when used with # 38954x wheels and #385262 alu nuts. |
|
|
************************************************************************************************* |
|
(click to enlarge) |
|
|
(click to enlarge) |
389163 XRAY Micro Motor 370 SuperSize
New premium 370 Supersize Micro Motor give 30% better performance (more power, more punch) than original 300 Supersize Micro Motor. Factory pre-assembled with surface-mount capacitor circuit board (no capacitors to solder), special noise filter, and pre-installed wires.
Fits: M18, M18T, M18MT |
|
|
************************************************************************************************* |
|
(click to enlarge) |
382107 Set of Suspension Arms 6° Caster - Hard (2)
Set of 2 molded harder-composite front upper suspension arms for XRAY M18 and NT18. These new arms have the same camber (-1°) as the stock upper arms, but less caster (6° caster vs. 12° caster stock). These arms provide improved steering, better handling into and out of corners. Highly recommended for serious racing and high competition⦠prepare to drop your lap times!
These new arms should only be used at the front of the car, not the rear.
Fits: M18, NT18 |
|
|
|
|