 |
 |
News  Product
New XRAY Solid Axle 1/10 Formula - Set |
|
 |
| |
|
|
| XRAY presents new authentic option parts for XRAY X1: |
|
(click to enlarge) |
|
|
|
#375001 XRAY Solid Axle 1/10 Formula - Set
Improves acceleration
Improves steering in high traction conditions
Lightweight
Perfect balance
Vibration-free
Graphite axle
Aluminum wheel hub
Clamp system |
|
(click to enlarge) |
|
|
|
Rear solid axle set includes graphite solid axle shaft, alu rear wheel hub and hardware. Super-light and tough graphite shaft gives perfect balance and smoothness for vibration-free operation. Improves acceleration and steering in high traction conditions.
Fits: X1 cars. |
|
(click to enlarge) |
|
|
(click to enlarge) |
|
|
|
The chassis features extra holes which allows to move the whole suspension more forward to extend the wheelbase of the car. The chassis features 3 wheelbase adjustment positions. The full backward position is identical to the original X1 chassis wheelbase. The other two extra positions extends the wheelbase of the car by 4 and 8mm. The longer the wheelbase is, the car is more stable and easier to drive. However longer wheelbase decreases car response, rotation and steering. Shorter wheelbase is recommended for smaller technical tracks and longer for more open tracks.
The 2.5mm chassis & top deck are made from high quality graphite material.
Fits: X1'19 & X1'18. |
|
(click to enlarge) |
|
|
(click to enlarge) |
|
|
|
This wing mount set allows to install rear wing fully independently from the rear pod plate. When the rear suspension is moving the wing stays in the same position which helps to improve car stability and increases traction, making the car easier to drive in all conditions. The wing mount plate features holes for wing mounting in exactly the same positions as the standard wing mount. Can be used either with the rear gear differential or ball differential.
The wing mount has multiple positions which allow higher or lower mounting of the rear wing to adapt to traction, conditions, and racing surfaces.
When traction is very low mainly on asphalt surfaces the upper holes allow a higher wing mounting position to generate more stability and traction off-power.
When traction is very high mainly on carpet surfaces the lower holes allow a lower wing mounting position to decrease traction rolling and make the car easier to drive.
Machined from premium 2.5mm graphite material.
Fits: X1'19. |
|
|
|
|
(click to enlarge) |
|
|
(click to enlarge) |
|
|
|
Chassis design, layout, and flex have significant influence on the handling of the X1. The 2.5mm chassis made from harder graphite material was developed for very-high traction conditions, or when using tires that offer a lot of steering which makes the car more difficult to drive. This chassis makes the car more stable and easier to drive, and eliminates oversteering.
The super-narrow chassis front allows for maximum traction while having excellent steering and cornering speed. The chassis has ideal torsional stability to help eliminate the scrub effect in high-speed corners.
|
|
(click to enlarge) |
|
|
|
| Fits: X1'18 & X1'19. |
|
(click to enlarge) |
|
|
(click to enlarge) |
|
|
|
High-performance, low-profile aerodynamic body designed to perfectly fit the X1 and work under all track conditions while keeping the coveted classic F1 look and style.
The front & rear of the body have been designed to provide balanced downforce for maximum stability and directed airflow onto the rear wing. The body & cockpit sides are as flat as possible to direct airflow around the body for maximum stability. The body is made from high-quality premium Lexan material.
|
|
(click to enlarge) |
|
|
(click to enlarge) |
|
|
(click to enlarge) |
|
|
(click to enlarge) |
|
|
|
Precision-molded composite spur gear for gear differential, 64-pitch. Popular sizes available.
Fits: X1, X10, XII and X12 cars |
|
(click to enlarge) |
|
|
(click to enlarge) |
|
|
|
XRAY self-designed, revolutionary, super-smooth gear diffs for 1/12 & 1/10 pan cars and 1/10 formula cars are a direct replacement for the ball-differential. Complete sets which require no other extra parts and no extra adjustments.
Using the gear differential makes the car more stable and easier to drive, especially in high-traction conditions. The gear diff increases on-power steering which is needed on almost all types of tracks. A must have for every racer.
|
|
(click to enlarge) |
|
|
|
The complete gear differential set includes a composite case and cover, precision-molded internal satellite gears made from special XRAY-developed composite material, all ensuring long lifespan and super-smooth efficient operation. A super-strong hollow steel shaft ensures maximum reliability and strength.
The advantage of the gear diff is that it is maintenance-free. When the diff is correctly built, there is no need for maintenance for a very long time, no need for frequent oil changes, and no leakage due to a superior sealing system.
Fit:
#374900 - all XII and X12 cars
#374901 - all X1 cars
#374902 - all X10 cars
|
|
(click to enlarge) |
|
|
(click to enlarge) |
|
|
|
| CNC-machined graphite suspension arms made from 2.5mm premium-grade graphite material. The arms are 5mm wider which makes the front track-width 10mm wider in total. Increasing the front track-width makes the car easier to drive in high-traction conditions. |
|
(click to enlarge) |
|
|
|
| Fit: X1'17 & X1'18. |
|
(click to enlarge) |
|
|
|
#371016 X1'18 Alu Chassis 2.0mm - 7075 T6
Increases traction, steering & stability in specific conditions
For high and very high traction tracks
Swiss 7075 T6
2mm thick
Black anodized
Laser engraved
|
|
(click to enlarge) |
|
|
|
X1 chassis CNC-machined from 2mm premium Swiss 7075 T6 aluminum and additionally black coated. Designed & developed to increase traction, stability, and steering in specific conditions. The alu chassis provides better control and makes the car easier to drive. Recommended for high and very-high traction tracks. 24mm narrower than previous chassis versions, eliminating contact with the track in corners while rolling, and offering improved cornering speed. Includes a slot for a composite battery backstop which allows 5mm battery position adjustment when using the most frequently used cross-chassis alignment configuration. For use with #371148 alu rear pod plate.
Fits: X1'18. |
|
(click to enlarge) |
|
|
|
CNC-machined from Swiss 7075 T6 aluminum, this X1 chassis contains special cutout openings for increased flex. This chassis is recommended for and works extremely well on medium and high-traction tracks; not recommended for very-high traction conditions, where the #371016 Alu Chassis works better. This alu flex chassis generates more traction and gives improved steering. Used successfully by Team XRAY at numerous races, this chassis is a must have for every serious racer. 24mm narrower than previous chassis versions, eliminating contact with the track in corners while rolling, and offering improved cornering speed. Includes a slot for a composite battery backstop which allows 5mm battery position adjustment when using the most frequently used cross-chassis alignment configuration. For use with #371148 alu rear pod plate.
Fits: X1'18. |
|
(click to enlarge) |
|
|
(click to enlarge) |
|
|
|
2mm graphite chassis developed to provide the best possible traction in low-traction conditions. The thinner chassis allows the car to flex more and generate more overall traction. 24mm narrower than previous chassis versions, eliminating contact with the track in corners while rolling, and offering improved cornering speed. Includes a slot for a composite battery backstop which allows 5mm battery position adjustment when using the most frequently used cross-chassis alignment configuration. For use with #371149 graphite rear pod plate.
Fits: X1'18. |
|
(click to enlarge) |
|
|
(click to enlarge) |
|
|
|
| Optional downforce-adjustable composite front wings, approved for ETS race series. Available in two colors. |
|
(click to enlarge) |
|
|
(click to enlarge) |
|
|
(click to enlarge) |
|
|
|
New 2mm graphite chassis was developed to provide the best possible traction in low-traction conditions. The thinner chassis allows the car to flex more, which generates more overall traction.
Includes a new 2-position option for pod link mounting; the first outer position is standard, while the new inner position allows for angled mounting of the pod links to improve in-corner steering. Also features a new, more frontward position for mounting the central mount plate for the new short shock.
For use with #371149 graphite rear pod plate.
Fits: X1'17. |
|
(click to enlarge) |
|
|
(click to enlarge) |
|
|
|
Front anti-roll bar made from special spring steel material, designed to work with the ball-bearing roll bar mounting system.
Anti-roll bar wires are available in different thicknesses (1.11.4mm) to precisely tune the handling of your car.
Fits: X1'17. |
|
(click to enlarge) |
|
|
|
#371010 X1'17 Alu Chassis 2.0mm - 7075 T6
Increases traction, steering & stability in specific conditions
For high and very high traction tracks
Swiss 7075 T6
2mm thick
Black anodized
Laser engraved
|
|
(click to enlarge) |
|
|
|
X1 chassis CNC-machined from 2mm thick premium Swiss 7075 T6 aluminum and additionally black coated. Designed & developed to increase traction, stability, and steering in specific conditions. The alu chassis provides better control and makes the car easier to drive. This innovative alu chassis was extensively tested and is recommended for high and very high traction tracks. Includes a new 2-position option for pod link mounting; the first outer position is standard, while the new inner position allows for angled mounting of the pod links to improve in-corner steering. Also features a new, more frontward position for mounting the central mounting plate for the new short shock.
For use with alu pod plate #371148.
Due the nature of the aluminum material and the machining process, it is normal that the chassis may be slightly bent in the longitudinal direction.
Fits: X1'17. |
|
(click to enlarge) |
|
|
|
Newly-designed chassis CNC-machined from Swiss 7075 T6 aluminum contains special cutout openings for increased flex. This chassis is recommended for and works extremely well on medium and high traction tracks; not recommended for very high traction conditions, where the #371010 Alu Chassis works better.
This new alu flex chassis generates more traction and gives improved steering. Used successfully by Team XRAY at numerous races, this chassis is a must have for every serious racer. Includes a new 2-position option for pod link mounting; the first outer position is standard, while the new inner position allows for angled mounting of the pod links to improve in-corner steering. Also feature a new, more frontward position for mounting the central mount plate for the new short shock.
For use with alu pod plate #371148.Due the nature of the aluminum material and the machining process, it is normal that the chassis may be slightly bent in the longitudinal direction.
Fits: X1'17. |
|
|
|
|
(click to enlarge) |
|
|
(click to enlarge) |
|
|
|
Alu lower servo saver arm CNC-machined from premium Swiss 7075 T6 aluminum for superior strength and reliability. Orange color. (Color may vary slightly between products.)
New alu servo saver allows easy Ackermann adjustment.
|
|
(click to enlarge) |
|
|
(click to enlarge) |
|
|
(click to enlarge) |
|
|
|
| Newly-designed aluminum chassis with special cutout openings for increased flex. This chassis is recommended for and works extremely well on low-to-medium traction tracks. Not recommended for very high traction conditions where the #371005 - Alu Chassis works better. This new alu flex chassis generates more traction and improves steering. Used successfully by XRAY team at all latest races, a must have for every serious racer. |
|
(click to enlarge) |
|
|
(click to enlarge) |
|
|
|
Optional front wing and rear wing with adjustable downforce approved for 2015/2016 ETS season.
The rear wing is assembled via the mounting system which features a graphite mount and aluminum stands. Using shims between the wing and the alu stands, the position of the wing can be easily adjusted for various track conditions. The height of the wing can be adjusted by changing the mounting position on the graphite plate. The rear wing has adjustable downforce by the use of an optional insertable middle wing rib.
|
|
(click to enlarge) |
|
|
(click to enlarge) |
|
|
(click to enlarge) |
|
|
|
| Side springs for pan cars and formula cars. The side springs and spring caps feature a straight design (compared to the previously-used conical springs) to improve side traction and handling. The straight springs have more consistent and smoother compression which results in smoother out-of-corner exit as well as helping to prevent traction rolling. Set of 2. |
|
(click to enlarge) |
|
|
|
| Fit: XII, X12, X10 and X1 cars. |
|
(click to enlarge) |
|
|
(click to enlarge) |
|
|
|
Ultimate-match coil shock springs for pan cars and formula front suspension offer an additional range of choices to fine-tune your car. Powder color-coded for quick & easy identification. Set of 2.
Developed through extensive testing and racing experience. Stiffness is controlled by the thickness of the wire and the number of coils; softer springs have a lower "C" value, stiffer springs have a higher "C" value.
|
|
(click to enlarge) |
|
|
|
| Fit: XII, X12, X10 and X1 cars. |
|
(click to enlarge) |
|
|
(click to enlarge) |
|
|
|
| Aluminum 1-piece servo mount eliminates unwanted tweak. Improves steering characteristics. CNC-machined from premium Swiss 7075 T6 aluminum. Orange color. Color may slightly vary between products. |
|
(click to enlarge) |
|
|
(click to enlarge) |
|
|
|
Aluminum X1 chassis designed & developed to increase traction, stability & steering in specific conditions. The alu chassis provides a better control and makes the car easier to drive. This innovative alu chassis was extensively tested and is recommended for low, medium and high traction tracks.
Chassis is CNC-machined from 2mm thick premium Swiss 7075 T6 and is additionally black coated.
|
|
(click to enlarge) |
|
|
(click to enlarge) |
|
|
|
#371290 X1 Alu Body Post Plate
Universal body mount
Fits most popular front wings
No need to make additional holes in body
Easy mounting
4mm height |
|
|
|
|
