xrayxrayHome XRAY homeXRAY X-shopXRAY X-forumRCAmerica
supportsearchcontactguestbooksite map
newsproductsaboutusworldwide headlines

 

XRAY presents new authentic option parts for XRAY XB2 car:

click to enlarge
(click to enlarge)


#326182 Stainless Steel Weight 17g – Front
#326183 Stainless Steel Weight 17g - Front-Middle
#326184 Stainless Steel Weight 7g - Middle

• Small size
• Clean layout
• Results in lower CG
• Quick & easy install
• Stainless steel
• Marked for easy identification

click to enlarge
(click to enlarge)


Optional stainless steel weights for front, front-middle and middle of the XB2 cars. Small & easy to install chassis weight with clean layout made from stainless steel. Quick & easy attachment to chassis. Marked with weight value for easy identification.

click to enlarge
(click to enlarge)

click to enlarge
(click to enlarge)


Fits: XB2 cars.



click to enlarge
(click to enlarge)


#326170 XB2 Alu + Graphite Fully Adjustable Battery Holder

• Fully adjustable holder
• Eliminates play and battery movement
• Fits shorty pack hard case batteries
• Unique design
• Premium graphite & aluminum material

click to enlarge
(click to enlarge)


Fully adjustable aluminum and graphite battery holder that allows to use standard hard case batteries of various dimensions from different manufacturers. To eliminate the play and battery movement, the height, width and length are fully adjustable. Slots in the graphite backstops allow to adjust the length and width. After installing the battery in place graphite backstops are pushed next to the battery and tightened with screws to alu mounts. Swivel battery strap is then assembled and tightened with alu nut.

The adjustable holder and the battery backstops are CNC-machined from lightweight aluminum and the battery holders are machined from premium lightweight graphite material.

Fits: XB2 & XT2 cars.



click to enlarge
(click to enlarge)


#323516 Lexan Front Wing DIV

• Increases front downforce
• Very strong
• Lower or upper mounting alternative
• Multiple mounting positions
• Super lightweight
• Premium Lexan material
• 1 piece with 2 different mounting alternatives

click to enlarge
(click to enlarge)


Stylish, effective wider front wing works perfectly with XRAY XB2 body and increases front down force. Multiple mounting positions allow to change the position of the wing and alter the down force. Made from strong high quality Lexan™ material.

Fits: XB2 cars.



click to enlarge
(click to enlarge)


#323515 Lexan Rear Wing Center Fin - ZAP

• Maximizes airflow efficiency
• Super lightweight
• Very strong
• Premium Lexan material

click to enlarge
(click to enlarge)


Stylish, effective rear center fin was developed and long term tested to maximize the rear wing air flow efficiency. Center fin is mounted on #323513 Lexan Rear Wing – RANK or #323517 Lexan Rear Wing - TEC. Made from strong high quality Lexan material.

Fits: XB2 & XB4 cars.



click to enlarge
(click to enlarge)


#323517 Lexan Rear Wing - TEC

• Increases rotation into the corner
• Increases traction out of corner
• Very strong
• Super lightweight
• Premium lexan material

click to enlarge
(click to enlarge)


Stylish, effective rear wing works perfectly with XRAY XB2 body. Flat design helps to get more rotation coming into the corner and increases traction coming out of corner. Made from strong high quality Lexan material.

Fits: XB2 & XB4 cars.



click to enlarge
(click to enlarge)


#321268 Graphite Gear Box Height Adjustment Plate
#321269 Graphite Gear Box Height Adjustment Plate
#324013 Alu Front-Mid Motor (3 Gears) Plate - Lowered -2mm - 7075 T6

• Increases forward traction
• Allows super-low ride height
• For high-traction conditions
• Keeps drive shafts linear
• Less rolling in corners
• Two different ride height plates available

click to enlarge
(click to enlarge)


To increase performance in high-traction conditions, the XB2 can use a super-low ride height. To keep the drive shafts linear, the gear box can be raised by 2mm using optional graphite plates.

With two different ride-height adjustable plates, you can raise just the gear box or the entire rear suspension.

Fits: XB2 cars.

click to enlarge
(click to enlarge)

click to enlarge
(click to enlarge)



click to enlarge
(click to enlarge)


#322572 Alu Steering Plate Rearward Linkage Mounting - Swiss 7075 T6

• More linear steering
• More predictable handling
• More precise steering
• Easily adjustable Ackermann positions

click to enlarge
(click to enlarge)


Alu steering plate for rearward linkage mounting allows mounting the steering linkages more rearwards which makes the steering more linear and makes the car more predictable. Ackermann is easily adjusted via steering link mounting positions on the steering plate. The alu steering plate gives more precise steering, but makes the steering more aggressive. CNC-machined from premium Swiss 7075 T6 aluminum.

Fits: XB2 & XT2 cars.



click to enlarge
(click to enlarge)


#324000 Short 2-Pad Slipper Clutch Set - Shocks in Front

• Allows frontward shock absorber mounting position
• Super narrow
• Externally adjustable
• Quick & easy tuning
• Ultra-efficient
• Lightweight
• Increases stability
• Higher cornering speed
• Better landings

click to enlarge
(click to enlarge)


Redesigned slipper clutch set allows the rear shock absorbers to be mounted frontwards. Frontward mounting position increases stability on surfaces where the rear of the car collapses, particularly in high-speed corners. Team drivers also prefer this position on low-grip tracks.

Power from the motor is transferred to the drivetrain via an externally-adjustable central slipper clutch for quick & easy tuning. The 2-pad slipper clutch ensures super-smooth clutch operation and efficient, consistent braking. It is very easy to make ultra-fine adjustments to the slipper clutch externally.

The slipper clutch pads are made from ultra-efficient SLS material with very-high slip efficiency, thus allowing very precise slip adjustment.

The lightweight slipper plates are machined from premium Swiss 7075 T6, additionally hardened before a final black surface treatment.

The plates have a machined relief which decreases the friction surface to assist with clutch slip adjustment. With this plate design, pressure is focused on the circumference of the clutch pads for increased efficiency.

Set includes 2-pad spur gears:
• #365775 Composite Slipper Clutch Spur Gear 75T/48P
• #365778 Composite Slipper Clutch Spur Gear 78T/48P

Fits: XB2 Dirt & XT2 Dirt.



click to enlarge
(click to enlarge)


#329708 Body for 1/10 2WD Off-Road Buggy 0.5mm - Beta 2 - Light

• Ultra-lightweight
• High-performance
• Low-profile
• Super-smooth airflow
• Increases steering
• Increases stability
• Improves handling in jumps
• Reduces roll
• Improves rotation

click to enlarge
(click to enlarge)


The optional ultra-lightweight, completely redesigned, high-performance, low-profile Beta 2 body with super-smooth airflow and all-new downforce areas. The Beta 2 body gives increased steering & stability while also improving handling in jumps. Lower weight reduces the roll of the car and improves rotation in corners.

The front part of the body has a redesigned high-downforce area. The sides of the body have upper downforce areas to generate more mid-body downforce, and the straight sidewalls improve stability. The upper part of the body was redesigned with a smooth flow channel.

Different XB2 bodies are available in different thicknesses for fine tuning the performance of the car.

Fits: XB2 cars.



click to enlarge
(click to enlarge)


#323112-G XT2 Composite Suspension Arm Rear Lower - Graphite

• Reliable
• Durable
• Special graphite composite mixture

click to enlarge
(click to enlarge)


Rear lower suspension arm redesigned to allow the shock absorbers to be mounted either frontwards or backwards.

Made from specially-formulated graphite composite material used for suspension arms, this arm is a perfect balance between reliability and performance; rigid enough for responsive feel and extreme durability.

Universal design rear arm can be used on both left & right sides. Suitable for high- and very-high-traction tracks.

Fits: XT2 cars.



click to enlarge
(click to enlarge)


#325324 Rear Drive Shaft 75mm with 2.5mm Pin - HUDY Spring Steel™
#325325 Rear Drive Shaft 72mm with 2.5mm Pin - HUDY Spring Steel™
#325326 Rear Drive Shaft 73mm with 2.5mm Pin - HUDY Spring Steel™

• Reliable
• Durable
• Various lengths for different situations

click to enlarge
(click to enlarge)


CNC-machined CVD rear drive shafts with 2.5mm pin for XB2 and XB4 cars, made from world-renowned HUDY Spring Steel™. Hardened with a proprietary hardening process, the drive shafts provide unbeatable lifetime and reliability.



click to enlarge
(click to enlarge)


#323354-G Composite Rear Upright - Graphite

• Special graphite composite mixture
• Increases stability
• Increases cornering speed
• For medium and high traction tracks
• Reliable
• Durable

click to enlarge
(click to enlarge)


Super-compact rear upright made from specially-formulated graphite composite material features multiple set-up options for upper & lower roll centers.

Upper roll center is adjustable via camber linkage & shims – up/down & in/out. Lower roll center is adjustable via eccentric inserts in 9 different positions – up/down & in/out.

The race-proven, 2-piece design allows fine-adjustment and increases durability as well as performance. The graphite rear uprights make the car more stable and increases cornering speed as well as overall strength of the car. The uprights are small in size but are very strong due to the special composite mixture used. Suitable for most track conditions, especially for medium- and high-traction tracks.

The upright fits on both left & right sides. Must be used with the #325324, #325325 or #325326 drive shafts.

Fits: XB2, XT2, XB4 cars.



click to enlarge
(click to enlarge)


#980320-T Titan Pin 3x20 (2)

• Titanium material
• Ultra-precise
• Super lightweight
• High durability
• Long life

click to enlarge
(click to enlarge)


Titanium pins, ultra-precision hand ground for high durability and long life. More than 40% lighter compared to standard steel pins. Dia. x length = 3mm x 20mm. Set of 2.

Fits: XB2, XT2 & RX8 cars.



click to enlarge
(click to enlarge)


#329901 2WD/4WD Rear Wheel Aerodisk with 12mm Hex - V2 - White (10)
#329913 2WD/4WD Rear Wheel Aerodisk with 12mm Hex - V2 - White (2)

• Redesigned countersunk center area
• Specially-designed 1/10 Off-Road Wheels
• Flexible yet durable material
• Excellent for high-competition racing
• Perfect fit
• 12mm internal hex
• Available as 2pcs set or 10pcs set

click to enlarge
(click to enlarge)


Specially-designed 2WD/4WD rear wheels with 12mm internal hex. The center countersunk area was redesigned to place the wheel nut deeper. Precision fit, perfect for high-competition racing. Made from flexible, durable material to withstand impacts. The side of the wheel is aerodynamic for maximum performance.

click to enlarge
(click to enlarge)


Special features of the wheel are visible from the inside: reinforcement ribs to make the wheels as stable as possible and eliminate deformation.

Fits: XB2 and XB4 cars.



click to enlarge
(click to enlarge)


#320901 XRAY XB2 Factory Team Upgrade for Carpet

• Factory Team upgrade for XB2C for carpet tracks
• Long-term used by Factory Team
• All-new alu upright design with multiple set-up options
• Lower roll center adjustment with 9 different positions
• Upper roll center adjustment up/down & in/out
• Longer drive shafts
• More forward traction
• Increases traction under braking
• Increases overall side grip & overall stability

click to enlarge
(click to enlarge)


Limited-quantity upgrade set to convert your XB2C into the same Spec version used by the Factory Team at carpet tracks. This complete set features all parts necessary for the upgrade: all-new rear aluminum uprights, aluminum upright plate, longer drive shafts, ball-bearings, eccentric bushings, and all necessary hardware.

The new aluminum uprights feature multiple set-up options for upper & lower roll centers. The upper roll center is adjusted at the camber linkage via shims in all directions up/down & in/out, while the lower roll center is adjustable via eccentric inserts in 9 different positions up/down & in/out.

This upgrade set was long-term tested and used by the Factory Team at major carpet races including EOS, XRS, MIBO, and other carpet tracks all around the world. The upgrade makes the XB2C more stable and increases overall side grip and forward traction. Traction under braking is also improved.

click to enlarge
(click to enlarge)


Fits: XB2'18 Carpet.



click to enlarge
(click to enlarge)


#326181 Stainless Steel Battery Weight 35g

• Easier to drive
• Improves landing
• Inserted under battery, directly on chassis
• Stainless steel material
• Adds weight
• Lowers CG

click to enlarge
(click to enlarge)


Specially-designed 35g stainless steel weight for placement beneath short battery pack to add weight as low as possible. Makes the car easier to drive and improves landing. A must-have option part.

Fits: XB2 and XT2 cars.



click to enlarge
(click to enlarge)


#320900 Complete XB2 Dirt Rear Suspension Conversion Set

• Complete conversion set
• Convert XB2’18 Carpet into dirt car
• Generates more traction
• Increases stability
• Used by factory team

click to enlarge
(click to enlarge)


Complete rear suspension conversion set including ball differential to convert XB2 Carpet 2018 version into a car suitable for clay tracks. This conversion set includes wide rear suspension arms from XB4 kit as well all other parts necessary to upgrade the car into the specs as used by the factory team as well Ty Tessmann at the recent Reedy Race.

Includes:
#323325 Alu Rear Longer Lower Susp. Holder - Narrow - Rear (10mm)
#323353-M Composite Rear Upright - Medium
#325002 Ball Adjust. Diff for 2.5mm Pin - Set - HUDY Spring Steel™
#325323 Rear Drive Shaft 71mm with 2.5mm Pin - HUDY Spring Steel™
#327310 Rear Suspension Pivot Pin 3x46 mm (2)
#363111-H Composite Suspension Arm Rear Lower Right - Hard
#363121-H Composite Suspension Arm Rear Lower Left - Hard
#365357 Alu Wheel Hub 12mm - Offset "+2.25mm" (2)
#367320 Rear Arm Pivot Pin (2)

Fits: XB2'18 Carpet.



click to enlarge
(click to enlarge)


#324910-G Composite Gear Differential Cover – Graphite
#324953-G Composite Gear Differential Case with Pulley 53T - Graphite

• Special graphite composite mixture
• Higher strength
• Lower weight

click to enlarge
(click to enlarge)


Gear differential case with 53T pulley and cover made from specially-formulated graphite composite mixture for increased strength and lower weight. Perfect balance between reliability and performance.

click to enlarge
(click to enlarge)


Fit: XB2 & XT2 cars.



click to enlarge
(click to enlarge)


#322210-G Composite C-Hub Right - Graphite
#322220-G Composite C-Hub Left - Graphite

• Special graphite composite mixture
• Durable
• Reliable
• For high & very high traction conditions
• More predictable handling

click to enlarge
(click to enlarge)


GRAPHITE molded composite C-hubs. The specially-formulated graphite composite material is a perfect balance between reliability and performance. Make the handling more predictable. Suitable for most track conditions, especially for high & very high traction tracks.

Fit: XB2 & XT2 cars.

click to enlarge
(click to enlarge)



click to enlarge
(click to enlarge)


#321190 XB2 Graphite Front Wing Holder

• Lower CG
• Less roll
• Increased steering

click to enlarge
(click to enlarge)


High-quality CNC-machined front wing holder made from premium graphite material. Complete set including shims and mounting hardware. Allows the wing to be mounted lower and more forward which results in lower CG, less roll, and increased steering.

Fits: XB2 cars.



click to enlarge
(click to enlarge)


#322250-G Composite Steering Block - Graphite

• Special graphite composite mixture
• Narrower design
• Increased traction
• Decreased roll

click to enlarge
(click to enlarge)


Molded composite motor gear box made from premium composite material accommodates 3 gears. The graphite molded gear box is lighter and stronger, with a narrower design to fit the narrower suspension holders, decreasing roll while increasing traction. All parts fit together perfectly, and give super-easy access to the rear differential. The durable gear box houses the differential and rear transmission, allowing the mounting of the rear roll center holder, motor plate, and rear shock tower.

Fits: XB2 Carpet cars.



click to enlarge
(click to enlarge)


#322250-G Composite Steering Block - Graphite

• Special graphite composite mixture
• Reliable
• Durable
• Increases stability
• Increases cornering speed
• For high and very high traction tracks

click to enlarge
(click to enlarge)


Molded composite steering block from specially-formulated graphite composite material is a perfect balance between reliability and performance. Make the car more stable and are suitable for most track conditions, especially for high- and very-high-traction tracks.

Fits: XB2 & XT2 cars.



click to enlarge
(click to enlarge)


#323353-G Composite Rear Upright – Graphite

• Special graphite composite mixture
• Durable
• Reliable
• Increases stability
• Increases cornering speed
• For high and very high traction tracks

click to enlarge
(click to enlarge)


Super-compact rear upright made from specially-formulated graphite composite material. Perfect balance between reliability and performance, for use on left or right side. Suitable for most track conditions, especially for high- and very-high-traction tracks. The graphite rear uprights make the car more stable and increase cornering speed as well the strength of the car. The compact rear uprights are small in size but are very strong thanks to the special composite mixture used.

Features 7 different upper roll center positions. The rear uprights feature 0° toe to ensure stability and to prevent suspension geometry changes in hard crashes.

For maximum drivetrain reliability, larger 5x12mm ball-bearings are used in the outer position with increased dynamic load. On the inner position, smaller 5x10mm ball-bearings are used to minimize unsprung weight.

Fits: XB2 and XT2 cars.



click to enlarge
(click to enlarge)


#324051 Composite Gear Cover - Front Motor Position

• Strong composite material
• Covers gear
• Protects body shell
• Light weight

click to enlarge
(click to enlarge)


Optional molded composite gear cover made from strong, lightweight composite material. Covers the gear to avoid contact with body shell.

Fits: XB2 Carpet and XT2 cars.



click to enlarge
(click to enlarge)


#322084 Graphite Shock Tower Front 4.0mm - Lower
#323084 Graphite Shock Tower Rear 3.5mm - Lower
#368121 Alu Front Shock Body 32mm - Hard Coated (2)
#368161 Front Hardened Shock Shaft 42mm (2)

• Improved landing
• Less roll
• Improves stability
• Suggested for high traction conditions
• All parts available individually

click to enlarge
(click to enlarge)


Low shock absorbers with shorter body complemented with shorter shock shaft and lower shock towers. Recommended for high-traction tracks, reducing front roll, allowing to run without front sway bar and allowing to use more droop for better landing.

Fit: XB2 cars.

click to enlarge
(click to enlarge)



 
  T4 Is Double ETS Champion    
  XT8E Wins At 1/8 Off-Road ROAR E-Nats In US    
  GTX8 Is European Vice-Champion    
  XT8 Is US National Champion    
  XB4 & XT2 Are EOS 2016/2017 Champions    
  XB8E'17 Wins At The NEO Race    
  X12 Is Double European Champion    
  X12 Wins At 2017 ROAR Nationals    
  T4 Wins At 2017 TITC    
  XRAY T4 Double Win At Snowbird Nationals 2017    
  The largest and most powerful set-up sheet database in the world..    
 
   
  All artwork & webdesign by XRAY. All content © 1999 - 2009 by XRAY • Terms of use • Privacy & security