|

(click to enlarge) |
|
|

(click to enlarge) |
|
|
|
M18 PRO chassis set in different stylish graphite finish. Includes CNC-machined graphite parts (chassis, top deck, battery holder and top bumper upper holder), molded composite parts (battery backstops, rear bumper), alu LiPo battery strap posts and mounting hardware. |
|

(click to enlarge) |
|
|

(click to enlarge) |
|
|

(click to enlarge) |
|
|

(click to enlarge) |
|
|

(click to enlarge) |
• Micro pinion gears
• For standard micro motors
• 48 pitch modul
• High-performance
• Tough & durable
• Steel material
• Precision-cut
• Chamfered edges
• Run-in
• Indvidually inspected
• Complete range available
|
|
|
High-performance 9 tooth, 48-pitch micro pinion gear, manufactured from special steel for toughness and durability. Precision-cut teeth with chamfered edges. Run-in for smooth operation. |
|

(click to enlarge) |
|
|
|
Fits: M18, M18PRO, M18T, M18MT. |
|
|
************************************************************************************************* |
|

(click to enlarge) |
|
|

(click to enlarge) |
389912 Wheel Aerodisk M18 PRO (Hex Hub) - Rubber (2+2)
Solid dish rims for rubber tires. Wheels for use with drive shafts with hex adaptors ONLY. Will not fit on original M18 with original wheel mounting system. Set of 4 (front and rear).
Fits: M18 PRO
Will also fit M18/NT18 when used with drive shafts with hex adaptors and #385262 alu nuts. |
|
|
************************************************************************************************* |
|

(click to enlarge) |
|
|
|
************************************************************************************************* |
|

(click to enlarge) |
|
|

(click to enlarge) |
CNC-machined alu micro wheel axles for drive shafts with hex adaptors are made from tough, high-grade T6 aluminum. Ultra-smooth operation, high-precision design and fit. Provides extra strength for use with high-performance motors. Features 1.0mm and 2.0mm offset for wider track-width.
For use with hex-hub micro wheels only; will not fit original M18. Set of 2.
385253 M18PRO Alu Wheel Axle - Offset +1mm (2)
385254 M18PRO Alu Wheel Axle - Offset +2mm (2) |
|
|
************************************************************************************************* |
|

(click to enlarge) |
|
|

(click to enlarge) |
XRAY introduces a new 5-cell (6.0V) and a new 6-cell (7.2V) inline battery packs made from ultra-high performance Intellect IB1400mAh NiMH cells. These 2/3A cells offer low resistance and they will maintain their high voltage under load, allowing them to easily provide power to high-powered servos without a performance decrease. |
|
|
************************************************************************************************* |
|

(click to enlarge) |
|
|

(click to enlarge) |
385203 Alu Drive Shaft with Hex Adapter - Set (2)
CNC-machined drive shafts with hex adaptors are made from tough, high-grade T6 aluminum and high-strength steel pins and fasteners. Ultra-smooth operation, high-precision design and fit. Provides extra strength for use with high-performance motors. This set of two drive shafts comes completely assembled, ready to install. A "must have" for serious drivers involved in high-competition racing. For use with hex-hub micro wheels only.
Fits: M18 PRO
Will also fit M18/NT18 when used with # 38954x wheels and #385262 alu nuts. |
|
|
************************************************************************************************* |
|

(click to enlarge) |
|
|

(click to enlarge) |
389163 XRAY Micro Motor 370 SuperSize
New premium 370 Supersize Micro Motor give 30% better performance (more power, more punch) than original 300 Supersize Micro Motor. Factory pre-assembled with surface-mount capacitor circuit board (no capacitors to solder), special noise filter, and pre-installed wires.
Fits: M18, M18T, M18MT |
|
|
************************************************************************************************* |
|

(click to enlarge) |
382107 Set of Suspension Arms 6° Caster - Hard (2)
Set of 2 molded harder-composite front upper suspension arms for XRAY M18 and NT18. These new arms have the same camber (-1°) as the stock upper arms, but less caster (6° caster vs. 12° caster stock). These arms provide improved steering, better handling into and out of corners. Highly recommended for serious racing and high competition… prepare to drop your lap times!
These new arms should only be used at the front of the car, not the rear.
Fits: M18, NT18 |
|