Alu shims 3x6mm size, 1mm thick. Orange color, set of 10. 

Alu shims 3x6mm size, 2mm thick. Silver color, set of 10. 

Ball 5.8mm with hex cavity, for connection to molded composite ball joints. Set of four. 

The NT1 chassis was redesigned to achieve better steering characteristics. The front of the chassis was widened to make the car less twitchy and easier to drive, the new front middle shaft holder is positioned differently on the chassis, and there are new holes for a new battery mounting system. 

Molded composite adjustable ball-bearing hub. Set of 4.  

Molded composite eccentric suspension pin inserts with 2 different offset positions. Set of 4 insert frames allows pins to have entire range of adjustment (+1.5, +0.5, -0.5, -1.5mm). 

CNC-machined adjustable turnbuckles, 22mm length, made from tough HUDY Spring Steel™. Set of 2. 

Lower & upper rear RIGHT bulkhead set molded from special composite mixture.
 

Lower & upper rear LEFT bulkhead set molded from special composite mixture. The rear upper camber link  

Molded composite rear bulkhead cover. 

CNC-machined rear roll center bridge made from thick, top-grade graphite. Includes multiple roll center mounting positions. 

CNC-machined rear shock tower made from top-grade 3.0mm thick FRP material. Includes multiple shock upper mounting positions. 

Molded composite suspension arm, rear lower. Used on either left or right side. 

Molded composite 5.8mm ball joints for rear upper camber link. Set of 4. 

Steel 5.8mm pivot balls with double shoulders and 4mm hex slot in one end. Set of 4. 

Molded composite rear upright with 2 roll center positions, used on left or right side. 

Rear anti-roll bar wire, 2.0mm for adjusting rear anti-roll bar stiffness. 

CNC-machined steel ball joint for rear anti-roll bar. Set of 2. 

Molded composite 5.8mm ball joints for rear anti-roll bar linkages. Set of 4. 

CNC-machined brake cam post made from tough 7075 T6 alu. 

Molded composite rear bulkhead brake cross plate + anti-roll bar clamps. 

Laser-cut, heat-treated, precision-ground ventilated brake disk for NT1 ensures vibration-free operation. 

High-precision, ultra-efficient steel brake pads for NT1 are laser cut and precision ground on both sides for an ultra-smooth surface finish to guarantee maximum braking efficiency. Set of 2. 

Ferodo® fiber brake pads for NT1, must be glued onto #334120 steel brake pads. Set of 2. 

CNC-machined brake disk adapter made from tough 7075 T6 aluminum. Includes factory-pressed pins (non-replaceable).  

CNC-machined drive axle for NT1 made from world-renowned HUDY Spring Steel™. Used for front or rear with standard drive shafts (not for use with CVD sets). 

CNC-machined, premium aircraft aluminum standard offset wheel hubs for XRAY NT1, a direct replacement for composite wheel hubs. These wheel hubs are strategically machined for optimum strength, balance, and lightness, and are marked for easy identification. Secured on drive axle by setscrew. Set of 2 hubs in each package. 

CNC-machined rear drive shaft (60mm) made from world-renowned HUDY Spring Steel™. Used for REAR only. Use with #335210 drive axle. 

PUR® reinforced rear drive belt. 5.5 x 177mm. This belt is very thin and elastic as possible for an extremely efficient, low-friction drivetrain. 

2-speed layshaft is precision ground, heat-treated and polished for smooth operation, extra strength, and long life. 

Molded composite 20T belt pulley on main layshaft, drives rear belt. 

Steel 8.4mm pivot balls hardened and ultra-precisely hand ground for very high durability and long life. Set of 2.  

Composite M10 adjusting nut for capturing pivot balls in front steering blocks and rear uprights. Lighter than standard nut, easier mounting and usability. Fine tuning for serious racers. Set of 4. 

Rear lower inner pivot pins for NT1. Hardened for very high durability and long life. Set of 2. 

M3x3 setscrew, hex drive. Set of 10 pieces. 

M3x5 setscrew, hex drive. Set of 10 pieces. 

M3x8 setscrew, hex drive. Set of 10 pieces. 

M3x12 setscrew, hex drive. Set of 10 pieces. 

M3x16 setscrew, hex drive. Set of 10 pieces.
 

M4x6 setscrew, hex drive. Set of 10 pieces.  

M3x6 button-head machine screw, hex drive. Set of 10 pieces. 

M3x8 button-head machine screw, hex drive. Set of 10 pieces. 

M3x12 button-head machine screw, hex drive. Set of 10 pieces. 

M3x8 flat-head machine screw, hex drive. Set of 10 pieces.
 

M3x10 flat-head machine screw, hex drive. Set of 10 pieces.
 

New high-speed ball-bearings manufactured specially for XRAY. ID x OD x thickness (mm) = 5x8x2.5mm. Set of 2 pieces.
 

New high-speed ball-bearings manufactured specially for XRAY. ID x OD x thickness (mm) = 6x13x5. Set of 2 pieces.  

New high-speed ball-bearings manufactured specially for XRAY. ID x OD x thickness (mm) = 10x16x4. Set of 2 pieces.  

7mm dia. E-clip. Set of 10 pieces.  

Polished chrome pin. Dia. x length = 2mm x 8mm. Set of 10 pieces. 

Polished chrome pin. Dia. x length = 2mm x 10mm. Set of 10 pieces.