Alu shims 3x6mm size, 1mm thick. Black color, set of 10. 

Alu shims 3x6mm size, 1mm thick. Orange color, set of 10. 

Alu shims 3x6mm size, 2mm thick. Black color, set of 10. 

Alu shims 3x6mm size, 2mm thick. Orange color, set of 10. 

CNC-machined 5.8mm dia ball joint for anti-roll bar, made from premium lightweight 7075 T6 aluminum. Set of 2. 

Medium springs for #335540 Composite 2-Speed Gear Box Set allows for medium 2nd gear engagement point. Set of 2. 

2nd gear carrier (drum) CNC-machined from tough Swiss 7075 T6 alu. Orange color. 

1st gear drive flange CNC-machined from tough Swiss 7075 T6 aluminum. Includes factory-pressed (non-replaceable) high-quality German one-way bearing, hand-ground for maximum running precision and strength. 

XRAY precision-molded 45T spur gear (2nd gear) made from special composite material with optimal balance of hardness, toughness, and flexibility. Gives long life, minimal wear, and minimizing breakage and teeth stripping. Strategically lightened to reduce rotating mass.  

XRAY precision-molded 47T spur gear (2nd gear) made from special composite material with optimal balance of hardness, toughness, and flexibility. Gives long life, minimal wear, and minimizing breakage and teeth stripping. Strategically lightened to reduce rotating mass. 

XRAY precision-molded 48T spur gear (1st gear) made from special composite material with optimal balance of hardness, toughness, and flexibility. Gives long life, minimal wear, and minimizing breakage and teeth stripping. Strategically lightened to reduce rotating mass. 

XRAY precision-molded 50T spur gear (1st gear) made from special composite material with optimal balance of hardness, toughness, and flexibility. Gives long life, minimal wear, and minimizing breakage and teeth stripping. Strategically lightened to reduce rotating mass. 

XRAY precision-molded spur gear (2nd gear). 

XRAY precision-molded spur gear (2nd gear). 

XRAY precision-molded spur gear (2nd gear). 

XRAY precision-molded spur gear (1st gear). 

XRAY precision-molded spur gear (1st gear). 

XRAY precision-molded spur gear (1st gear). 

High-strength 15T pinion gear (1st gear) made from tough 7075 T6 alu and specially hardcoated for superior strength, light weight, and high durability. 

High-strength 17T pinion gear (1st gear) made from tough 7075 T6 alu and specially hardcoated for superior strength, light weight, and high durability.  

High-strength 18T pinion gear (1st gear) made from tough 7075 T6 alu and specially hardcoated for superior strength, light weight, and high durability.  

High-strength 20T pinion gear (2nd gear) made from tough 7075 T6 alu and specially hardcoated for superior strength, light weight, and high durability.  

High-strength 21T pinion gear (2nd gear) made from tough 7075 T6 alu and specially hardcoated for superior strength, light weight, and high durability.  

Set of two (2) XCA-clutch pinion gear tools aids in installing and removing XCA clutchbell pinion gears.  

Complete C-hub conversion set for GTX platform fits both nitro and electric powered GTX. The C-hub suspension is suited for most standard track conditions and makes the car more responsive and increases steering resulting into faster lap times.  

All-new redesigned side guards incorporate a larger bottom radius to make the car more stable on rough tracks, and increase the car???s longitudinal flex. 

The composite side guards protect the car, muffler, and fuel tank from side impacts. The side guards perfectly fit the chassis and seal against dirt. Molded from SOFT composite mixture for increased flex to generate more traction.
 

Lightweight version of GTX8 front bumper.  

Graphite front plate is CNC-machined from high-grade carbon graphite, ensuring highest strength with lightest weight.  

Front lower suspension arm for XB8 made from super-tough, high-tech composite material. Universal design allows the arm to be used on either left or right sides. 

Front lower suspension arm for XB8 made from super-tough, high-tech composite material. 

Molded lightweight front LOWER suspension arm made from specially-formulated graphite composite material.  

Front lower suspension arm for C-hub suspension molded from medium hardness composite mixture. 

Front lower suspension arm for C-hub suspension molded from specially-formulated graphite composite material.  

Front lower suspension arm for C-hub suspension molded from a new hard composite mixture.  

Front lower suspension arm for C-hub suspension molded from soft hardness composite mixture, super-tough, high-tech composite material. 

Front C-hub steering block molded from specially formulated composite material. Features alu inserts for increased durability. Fits larger outside ball-bearings for increased reliability and life-span. 

Authentic XRAY RIGHT-side 16 alu caster block is CNC-machined from premium Swiss 7075 T6 aluminum.  

Molded composite C-hub for RIGHT steering block. Made from high-tech composite material. Caster pre-set at 16. For use with matching left-side C-hub #352287.  

Authentic XRAY LEFT-side 16° alu caster block is CNC-machined from premium Swiss 7075 T6 aluminum.  

Molded composite C-hub for LEFT steering block. Made from high-tech composite material. Caster pre-set at 16. For use with matching right-side C-hub #352277. 

Front anti-roll bar for XB8, XT8 & GTX8 cars, 1.6mm thick.  

Front anti-roll bar for XB8, XT8 & GTX8 cars, 1.8mm thick.  

Front anti-roll bar for XB8, XT8 & GTX8 cars, 2.0mm thick.  

Front anti-roll bar for XB8, 2.2mm thick. Laser-engraved for easy identification. 

Front anti-roll bar for XB8, 2.3mm thick. Laser-engraved for easy identification.
 

Front anti-roll bar for XB8, 2.4mm thick. Laser-engraved for easy identification. 

Front anti-roll bar for XB8, 2.5mm thick. Laser-engraved for easy identification. 

Front anti-roll bar for XB8, 2.6mm thick. Laser-engraved for easy identification. 

Molded composite parts for XB8 servo saver.  

Rear lower suspension arm for XB9 made from super-tough high-tech composite material. Smart, universal design allows the same front arm to be used on both left and right sides. 

All-new hard XB9 suspension arm moulded from a new blend of XRAY's proprietary composite material.  

Molded lightweight composite rear lower suspension arm made from specially-formulated graphite composite material.  

CNC-machined 6.8mm dia mounting pivot ball with shoulder,made from premium lightweight 7075 T6 aluminum. Set of 4. 

CNC-machined 6.8mm dia mounting pivot ball,made from premium lightweight 7075 T6 aluminum. Set of 4. 

Optional graphite rear lower arm plate allows for stiffer the arms and makes the car more stable and easier to drive under high-grip conditions. 

Lightweight composite mud guard for rear suspension arms protects the rear drivetrain in wet & dirty track conditions. Set of L+R. 

Chassis side guard brace CNC-machined from high-grade graphite material.  

Reinforcement braces for rear composite brace, stiffen the composite brace and chassis for high-traction tracks. 

With this suspension holder, the roll center is moved by +2mm to allow for super fine roll-center adjustment.  

Lightweight yet ultra-strong rear upright molded from special graphite composite material.  

Alu shims 4x7.5mm size, 1mm thick. Black color, set of 4. 

Alu shims 4x7.5mm size, 2mm thick. Black color, set of 4. 

Rear anti-roll bar for XB8, XT8 & GTX8 cars, 1.8mm thick. 

Rear anti-roll bar for XB8, XT8 & GTX8 cars, 2.0mm thick. 

Rear anti-roll bar 2.2mm thick. 

Rear anti-roll bar 2.4mm thick. 

Rear anti-roll bar for XB8 & XT8, 2.5mm thick. Laser-engraved for easy identification.
 

Rear anti-roll bar 2.6mm thick. 

Rear anti-roll bar 2.8mm thick. 

Rear anti-roll bar 3.2mm thick. 

Alu rear wing shim for XB and XT series buggies and truggies. Provides additional support to prevent wing from pulling off from mounting screws. Set of 2. 

Molded composite rear wing shim for XB and XT series buggies and truggies. Provides additional support to prevent wing from pulling off of mounting screws. Black colour, set of 2. 

Composite center diff mounting plate set made from specially-formulated graphite composite mixture for increased strength and lower weight.  

Precision-cut shimming plates for raising the center diff mount when using 48T center spur gear (#355048). 

CNC-machined graphite ventilated brake disk.

When using this graphite brake disk, it is necessary to use hardened steel brake pads (#354121) by themselves without Ferodo fibre-style brake pads glued to them. 

Laser-cut, heat-treated, precision-ground ventilated brake disk for XB8 ensures vibration-free operation. Rotating mass is reduced without sacrificing strength or durability. 

Laser-cut, heat-treated, precision-ground ventilated super-lightweight brake disk for XB8, GTX and XT8 ensures vibration-free operation. 

Factory pre-assembled brake pad set for consistent and precise braking. High-precision, ultra-efficient steel brake pads are CNC-machined and precision ground on both sides for an ultra-smooth surface finish to guarantee maximum braking efficiency. 

New ultra-efficient brake pads from special slip-free material. Set of 4. 

Center mounting plate made from premium graphite material.  

Rubber-sealed differential case made from new specially-formulated graphite composite material. Lighter, tougher material with higher temperature and wear resistance, also holds the screws better secured in place. 

44-tooth large external bevel gear manufactured from HUDY Steel for drive ratio adjustment.  

45-tooth large external bevel gear manufactured from HUDY Steel for drive ratio adjustment.  

Precision-ground polished alu pin 3.5 x 26.6 mm for internal satellite gears used in large front & rear differentials #355004 and #355005. 

Complete Active Differential™ set for XB8.  

The 46T diff bevel gear for XRAY Active Diff™ is machined from special HUDY steel material which has been specially developed for gear-type products, additionally hardened and precision ground to fit the tightest tolerance requirements for perfect fit with the diff outdrives.  

Lightweight CNC-machined diff outdrive adapters for XB8 Active Diff. 

CNC-machined CVD drive axle made from premium lightweight Swiss 7075 T6 hardcoated aluminum. 

Drive axle for XRAY adjustable drive shafts. Drive shaft length adjustment uses 4 different connecting hole positions at the drive axle end to allow changes to overall driveshaft length.  

Hardcoated aluminum wheel axle with +1mm offset. Using these wheel axles will increase the overall track width by 2mm, making the car more stable and easier to drive.  

Hardcoated aluminum wheel axles with +2mm offset. Using these wheel axles will increase the overall track width by 4mm, making the car more stable and easier to drive. Set of 2. Wheel axles can be mounted in both front and rear. 

Hardcoated aluminum wheel nut with cover for XB8 wheels. Using these wheel nuts, you will never have problems anymore with dirt getting into the wheel axle assembly! Fits front and rear wheel axles.  

Polished chrome pin with flat spot, 3.0 x 16.8mm. Specially hand-ground for maximum precision. Set of 2. 

All-new radio plate design incorporates a new compact composite radio box. Batteries are now located at the front for better balance. Clean and smooth 1-piece plate design.  

The battery cable with switch connects the receiver battery to the receiver by way of an on/off switch. It is delivered together with switch cover.  

To reduce weight and lower the CG, all-new front upper pivot balls are combined with a steel threaded part for maximum strength.  

Optional brass M15 adjusting nut for capturing pivot balls in front steering blocks. The additional weight nuts are more than 3x heavier than standard alu adjusting nut. Great and handy for weight balance adjustment. Set of 2. Fits XB8.  

Molded composite ball cup for cushioning alu M15 alu adjusting nut against 13.9mm pivot ball.  

Set of composite molded shock pistons for two shock absorbers with five 1.5mm holes & two 1.0mm holes.  

Set of composite molded shock pistons for two shock absorbers with six 1.3mm holes & two 1.1mm holes. 

Set of composite molded shock pistons for two shock absorbers with six 1.4mm holes & two 1.1mm holes. 

Set of composite molded shock pistons for two shock absorbers with eight 1.2mm holes & two 1.2mm holes. 

Set of composite molded shock pistons for two shock absorbers with eight 1.3mm holes & two 1.2mm holes.  

CNC-machined 1-piece alu shock cap for XB8, made from premium lightweight 7075 T6 aluminum. Black coated. Set of 2.  

CNC-machined 1-piece alu shock cap for XB8, made from premium lightweight 7075 T6 aluminum. Features a small vent hole that makes shock assembly very predictable and easy, allowing excess shock oil to easily escape. Machined interior ridges ensure proper placement and sealing of the super-soft silicone membrane.  

Shock membrane for shock absorbers, made of soft molded rubber. The new shock membranes are now wider to fit the new big-bore shocks.  

Newly designed improved shock membranes provide more consistent feel during long finals with no sign of fade. Shock membrane for shock absorbers, made of soft molded rubber. The new shock membranes are wider to fit the big-bore shocks. The material has been also improved to guarantee the same damping characteristics from the beginning of the race to the end even after excessive loads. Set of 4. 

Shock membrane for XB8 shocks, made from soft molded rubber. Features internal bottom ribs to maintain shape. The specially-formulated rubber material of the shock membrane ensures equal damping characteristics from the beginning of the race to the end, even after extreme operation. Set of 4. Fits XB8. 

Shock membrane for XB8 shocks, molded from softer transparent rubber. 

Rubber valve for 2-way flow in shock pistons. Suitable for shocks in XB8, XT8, and GTX. 

Shock membrane for XB8 shocks, made from medium molded rubber. The cell shock membranes have less air gap that helps to generate more grip of the car.  

Foam inserts for XRAY shocks, go between shock upper mount and rubber membrane. Prevents membrane collapse. Provides slightly more steering, and more stability when landing from big jumps.  

Extra-strong fuel tank with integrated floating stone filter ensures that the fuel pickup will always be in the correct orientation even when the car isn’t. 

Alu monoblock engine mount provides solid engine mounting and easy adjustment. Monoblock design is stiffer than standard single engine mounts. 

Molded composite optional cover for air filter protects the filter and is recommended for muddy and rainy conditions. The cover is a direct fit for the 808 low-profile air filter assembly. 

Inner + outer low-profile foam filter elements, and a tube of air filter oil. Set of 10. 

Large capacity aluminum fuel filter set. This fuel filter is different from others as it is captured in a holder and will not turn as the result of vibration. 

Fuel filter set made from tough composite material and the aluminum cap is machined from premium aluminum. A sieve is installed in the fuel filter. The body of the fuel filter has a slot that enables the filter to sit in the holder perfectly and prevents the filter from turning. 

Molded composite fuel filter mount and fuel tubing holders.  

Thick silicone fuel tubing. 2.4mm ID, 1m length. Fluorescent yellow colour. 

XRAY’s self-designed GTX8 body – made from high-quality Lexan™ material – features high-downforce areas: front windscreen for proper airflow, and side downforce areas for higher stability.  

Alu conical shim 3x6x2.0mm. Black color. Set of 10. 

Alu conical shim 3x6x2.0mm. Orange color. Set of 10. 

Ultimate-match front coil shock springs for pan car front suspension offer an additional range of choices to fine-tune your car. Powder color-coded for quick & easy identification. Gold color. Set of 2.
 

Connection cable for plugging receiver battery pack into the receiver. Standard Futaba J connector on receiver end, micro battery connector on the battery end. 

M2x6 pan-head machine screw, Phillips drive. Set of 10 pieces. 

New high-speed ball-bearings manufactured specially for XRAY. ID x OD x thickness (mm) = 8x14x4. Set of 2 pieces. 

New high-speed ball-bearings manufactured specially for XRAY. ID x OD x thickness (mm) = 8x16x5. Set of 2 pieces. 

High-speed ball-bearings for XB8’18 and XB8E’18 manufactured specially for XRAY. ID x OD x thickness (mm) = 13x19x4. Set of 2. 

New high-speed ball-bearings manufactured specially for XRAY XB808. Sealed with rubber seal from one side and with steel seal from other side. ID x OD x thickness (mm) = 13x19x4. Set of 2 pieces. 

Flat washer, 3.2mm ID. Set of 10 pieces. 

Flat washer. ID x OD x thickness = 6mm x 18mm x 0.3mm. Set of 10. 

Flat washer. ID x OD x thickness = 6mm x 18mm x 0.5mm. Set of 10. 

Flat washer. ID x OD x thickness = 6mm x 10mm x 0.2mm. Set of 10. 

Flat washer. ID x OD x thickness = 6mm x 10mm x 0.3mm. Set of 10. 

Flat washer. ID x OD x thickness = 16mm x 20mm x 0.5mm. Set of 10 pieces.